1. 리니어 가이드에 사용되는 재료
1. Many linear guide materials use chromium bearing steel, common such as GCr15, and carburized bearing steel, such as G20CrMo, can also be considered. The structural design should pay attention to the quenching process requirements, otherwise there will be cracks and deformation.
2, linear sliders can be divided into: roller linear guides, cylindrical linear guides, and ball linear guides. Three types are used to support and guide the moving parts and perform reciprocating linear motion in a given direction. Depending on the nature of the conflict, linear motion guides can be divided into sliding conflict guides, rolling conflict guides, elastic conflict guides, and fluid conflict guides. Linear guides, ball screws, grinding racks, guides
둘째, 리니어 가이드의 분류
1. 선형 가이드 쌍은 일반적으로 가이드 레일, 슬라이더, 리버서, 롤링 바디 및 스틱으로 구성됩니다. 슬라이더와 가이드 레일 사이에 강구와 함께 롤링할 수 있는 상대 왕복 직선 운동을 위한 새로운 유형의 롤링 지지대입니다. 직접 슬라이딩 터치를 대체하기 위해 텀블링 바디는 리버서의 도움으로 궤도와 슬라이더에서 무한 루프를 완료할 수 있습니다. 간단한 구조를 가지고 있으며,
2. The advantages of small dynamic and static conflict coefficient, high positioning accuracy, and good accuracy persistence. Linear guides are also known as fine rolling linear guides, slide rails, linear guides, linear slides, and rolling guides. They are used in linear reciprocating applications that require accurate control of the parallelism of the worktable. They have a higher rated load than linear bearings. It can bear a certain torque and complete high-precision linear motion under high load.
3. The function of the linear guide is to support and guide the moving parts. Relying on the two or four rows of balls on both sides of the guide, the cyclic rolling of the two or four rows of balls drives the worktable to move smoothly in a given direction for reciprocating linear motion. Depending on the nature of the conflict, linear motion guides can be divided into sliding conflict guides, rolling conflict guides, elastic conflict guides, fluid conflict guides and other varieties.
셋째, 리니어 가이드의 정확도
1. The precision grades of linear guide rails are divided into (walking parallelism, the following takes the guide rail 100mm length as an example), general grade (no mark/C) 5μm, (H) 3μm, precision grade (P) 2μm, precision grade (SP) 1.5 μm, precision level (UP) 1μm depends on the use of different machines. Give the slider preload. Generally pre-compression is divided into pre-compression without pre-compression and heavy pre-compression. The greater the preload, the better the rigidity. Load: Generally, at the beginning of the selection, it is concluded that 1/3 of the rated dynamic load is the upper limit of the practical load. Therefore, it is generally added to the medium preload to ensure that there is no sinking. If the guide rail is used up and down, the guide rail has a directing effect. How much the sliding block rises is related to the used lead screw or other transmission methods, and has nothing to do with the sliding rail and the sliding block.
2. There are basically three types of different brands. Generally, gaps, light preloading, and medium preloading. The effect of the gap is to affect the walking accuracy, load bearing capacity and rigidity of the guide rail. In addition, the selection of guide rails with gaps can reduce the vibration and impact caused by reciprocating motion to a certain extent.
3. When loading, the slider will not sink much. It should be said that it will undergo elastic deformation. If you want to say how much, any guide rail material is not marked now, because it can be neglected.
넷째, 리니어 가이드와 리니어 베어링의 차이점
1. In terms of equipment: linear guides have higher precision than linear bearings, with greater load and greater stability.
2. In terms of cost: the same brand, linear guides are more expensive than linear bearings (domestic imitations are not counted).
3. From the market: linear guides have a wider range of applications than linear bearings, and linear bearings are relatively only suitable for preliminary processing.